Description

IC697CGR935 Hot Stand-by CPU Module GE Series 90-70 Cpu Parts,Io
Bus Terminator Plug,Ge Fanuc Terminal Block PLC CPU PARTS
Programmable PLC Communicate MODULES Robots DCS. This particular
fan tray provides an additional rack cooling system with two fans
per assembly. The rack fan is easily installed as an accessory with
the five slot and PACSystems RX7i nine-slot racks. The IC697ACC621
is ideal for systems where heat build-up is a potential problem.
The system offers a low noise level and uses ball bearings for an
extended life span. The manufacturer does recommend that the fans
be wired to the same power source as the PLC as this will ensure
the fans run each time the PLC is actively in use.To wire the fans,
use the parallel cable assembly supplied with the fan, which is
located on the back of the fan assembly. The IC697ACC621 fan tray
is compatible with the IC697CHS750, IC698CHS009, and IC697CHS109
racks. When mounted on the rack, the unit is located on the bottom
to allow the air to flow from the bottom to the top of the rack for
cooling. Easy installation is completed with only a #2 Phillips
head screwdriver. A minimum of 9 inches of space is needed between
racks to remove each individual fan and can be accomplished by
removing the three screws from the front lower panel of the rack.
Simply position the fan assembly on the bottom rack, and slide the
flange on the rear of the assembly. Align the holes, reinstall, and
tighten the screws. Each fan has a replaceable polyurethane filter
that can be cleaned between replacements if needed.

The IC697CGR935 module is a one slot controller in the GE Fanuc
series, which permits fluctuating point calculations mandatory for
CPU redundancy applications. The IC697CGR935 module in the Redundancy System is used as the
controller. There are two control methods to note when using the
IC697CGR935. In the GHS process, several single bus networks with
one redundant controller are used in each synchronized PLC. When
using the GDB process, multiple I/O networks are used with single
or double buses in each synchronized PLC. Each control method can
be easily activated and used without difficulty. In the IC697CGR935
module, the memory board delivers data, and program memory is
included with the module. The IC697CGR935 can be operated remotely
or by the three position RUN/STOP switch. Positioned on the front
of the module are the LEDs, which specify the status of the CPU.

Installation of the IC97CGR935 module should not be attempted without referring to the
appropriate Programmable Controller Installation and Hot Standby
CPU Redundancy Manual. The battery should be connected to one of
the module’s battery connectors. The key switch should be
positioned to MEMORY PROTECT OFF, and there should be no rack
power. Once module is installed in slot 1 of rack 0, power is
turned on. The top LED should blink indicating that the IC697CGR935
module is powered up. Once the diagnostic is finished effectively,
the top left LED stays on while the second and third LED will be
off. The MEMORY PROTECT LED which is the fourth LED, is off because
the key switch is in off position. Programming is now ready for the
CPU. The CPU can be programmed regardless of the placement of the
key. Once the program has been confirmed, the toggle switch can be
positioned in the appropriate operational mode.

IC697CHS750 A five slot rear mounting PLC rack, the GE Fanuc 90-70
IC697CHS750 accepts all IC697 PLC module types. Featured on the GE
Fanuc 90-70 IC697CHS750 are rear…
IC697CHS770 GE Fanuc 90-70 IC697CHS770 Accepts all IC697 PLC module
types, and IC687 (VME) I/O and Communications module types. GE
Fanuc 90-70 IC697CHS770 Accepts plug-in…
IC697CHS771 GE Fanuc 90-70 IC697CHS771 Accepts all IC697 PLC module
types, and IC687 (VME) I/O and Communications module types. GE
Fanuc 90-70 IC697CHS771 Accepts plug-in…
IC697CHS782 The GE Fanuc 90-70 IC697CHS782 Integrators Rack, 17
slot, Rear Mount, accepts 3rd Party VME modules which require 0.8″
spacing. GE Fanuc 90-70 IC697CHS782…
IC697CHS783 The GE Fanuc 90-70 IC697CHS783 Integrators Rack, 17
slot, Front Mount, accepts 3rd Party VME modules which require 0.8″
spacing. GE Fanuc 90-70 IC697CHS783…
IC697CHS790 The GE Fanuc 90-70 IC697CHS790 9-slot, Rear Mount Rack,
accepts all IC697 PLC module types and the GE Fanuc 90-70
IC697CHS790 accepts plug-in AC or DC IC697…
IC697CHS791 The GE Fanuc 90-70 IC697CHS791 9-slot Front Mount Rack,
accepts all IC697 PLC module types and the GE Fanuc 90-70
IC697CHS791 accepts plug-in AC or DC IC697…
IC697CMM711
GE IC697CMM711 Communications Coprocessor Module provides
communications control (CCM), remote terminal unit (RTU), and
general IC69* communications…

IC697CMM721 A GE Fanuc 90-70 IC697CMM721 is a Carrierband Lan
Interface (MAP 3.0). The GE Fanuc 90-70 IC697CMM721 has direct PLC
attachment to MAP Carrierband network. GE…
IC697CMM741 The GE Fanuc 90-70 IC697CMM741 MMS and TCP/IP Ethernet
LAN Controller is a single-slot module that is inserted directly
into the IC697 CPU rack. GE Fanuc…
IC697CMM742 The GE Fanuc 90-70 IC697CMM742 Ethernet Module connects
IC697 PLC to an IEEE 802.3 CSMA/CD 10Mbps Ethernet LAN via one of
three network ports: 10BaseT,…
IC697CPM790 GE Fanuc 90-70 IC697CPM790 is a 64 MHz, 32-Bit Floating
Point Central Processing Unit (CPU), 1 Mbyte Memory, for IC66*
Triple Modular Redundancy Systems. GE…
IC697CPM915 The GE Fanuc 90-70 IC697CPM915 is a 32 MHz 32-Bit
Floating Point Central Processing Unit, 1 Mbyte Memory. A GE Fanuc
90-70 IC697CPM915 has a single slot CPU…
IC697CPM925 GE Fanuc 90-70 IC697CPM925 is a 64 MHz, 32-Bit Floating
Point Central Processing Unit, 1 Mbyte Memory. GE Fanuc 90-70
IC697CPM925 Supports floating point…
IC697CPU731 12 MHz, 32 Kbyte Central Processing Unit, GE Fanuc
90-70 IC697CPU731 has 512 inputs and outputs (any mix). GE Fanuc
90-70 IC697CPU731 has up to 8K analog I/O….
IC697CPU771 GE Fanuc 90-70 IC697CPU771 2K inputs and outputs (any
mix) with up to 8K analog I/O. GE Fanuc 90-70 IC697CPU771 is
programmed and configured by MS-DOS or…
IC697CPU772 GE Fanuc 90-70 IC697CPU772 is a single slot PLC CPU
which allows floating point calculations. GE Fanuc 90-70
IC697CPU772 is programmedand configured by MS-DOS…
IC697CPU780 GE Fanuc 90-70 IC697CPU780 is required for Hot Standby
CPU applications, and supports floating point calculation. GE Fanuc
90-70 IC697CPU780 has 12K inputs…
IC697CPU781 GE Fanuc 90-70 IC697CPU781 16 MHz, 32-Bit, Expandable
Central Processing Unit, is a single slot CPU. GE Fanuc 90-70
IC697CPU781 is programmed and configured…
IC697CPU782 GE Fanuc 90-70 IC697CPU782 is a 16 MHz, 32-Bit,
Expandable, Floating Point Central Processing Unit. GE Fanuc 90-70
IC697CPU782 Supports up to 512 Kbytes of…
IC697CPU788 GE Fanuc 90-70 IC697CPU788 16 Mhz, 32-Bit Expandable
CPU for IC66* Triple Redundancy Systems, supports 512 Kbytes of
battery-backed expansion memory in the…
IC697CPU789 GE Fanuc 90-70 IC697CPU789 16 Mhz, 32-Bit Expandable
CPU for IC66* Triple Redundancy Systems, supports up to 12K
discrete inputs and outputs. The GE Fanuc…
IC697CPX772 GE Fanuc 90-70 IC697CPX772 96 Mhz, 32-Bit Point CPU
provides 512 Kbyte of battery-backed RAM memory. The GE Fanuc 90-70
IC697CPX772 contains 256K of…
IC697CPX782 GE Fanuc 90-70 IC697CPX782 is a 96 MHz, 32-Bit,
Floating Point, 1 Mbyte Memory Central Processing Unit. GE Fanuc
90-70 IC697CPX782 is a single slot CPU that…
IC697CPX928 GE Fanuc 90-70 IC697CPX928 is a 96 MHz, 32-Bit,
Floating Point, 6 Mbyte (Medium) Memory CPU. The GE Fanuc 90-70
IC697CPX928 single slot CPU provides three…
IC697CPX935 GE Fanuc 90-70 IC697CPX935 96Mhz, 32-Bit, Floating
Point, 1 MByte Fast Memory CPU is a single slot CPU with three
serial ports. GE Fanuc 90-70 IC697CPX935…
IC697HSC700 GE Fanuc 90-70 IC697HSC700 High Speed Counter (HSC)
module directly processes rapid pulse signals up to 200 KHz. GE
Fanuc 90-70
IC697LBR701 90-70 Documentation Library (paper manuals covering
most options)
IC697MCS704 GE Fanuc 90-70 IC697MCS704 is a Motion Controller For
the Series 90-70. GE Fanuc 90-70 IC697MCS704 is used in the 90-70
series. GE Fanuc 90-70…
IC697MDL240 GE Fanuc 90-70 IC697MDL240 120 Volt AC, Isolated,
16-Point Input Module provides 16 input points which are isolated.
GE Fanuc 90-70 IC697MDL240 input is…
IC697MDL241 GE Fanuc 90-70 IC697MDL241 240 Volt AC, Isolated
16-Point Input Module provides 16 isolated input points. . LED
indicators which give the ON-OFF status…
IC697MDL250 The 120 Volt AC, 32-Point Input Module, GE Fanuc 90-70
IC697MDL250, provides 32 input points in four isolated groups of 8
points each. This allows each group…
IC697MDL251 Discrete Input Modules GE Fanuc 90-70 IC697MDL251 have
16 Points – Four isolated groups of 4 points each. GE Fanuc 90-70
IC697MDL251 allows each group of four…
IC697MDL252 GE Fanuc 90-70 IC697MDL252, 12 VAC Input, has 32 Points
– Four isolated groups of 8 points each. GE Fanuc 90-70 IC697MDL252
allows each group of eight points…
IC697MDL253 The GE Fanuc 90-70 IC697MDL253 is a 24 Volt AC,
32-Point Input Module. GE Fanuc 90-70 IC697MDL253 provides 32 input
points in four isolated groups of eight…
IC697MDL254 As a 48 Volt AC, 32-Point Input Module the GE Fanuc
90-70 IC697MDL254 features 32 Points – Four isolated groups of 8
points each. The 48 volt AC Input…
IC697MDL340 GE Fanuc 90-70 IC697MDL340 is a 120 Volt AC, 2 Amp,
16-Point Output Module. GE Fanuc 90-70 IC697MDL340 provides a high
degree of inrush current which makes…
IC697MDL341 The 120/240 Volt AC, 2 Amp Isolated 12-Point Output
Module is the GE Fanuc 90-70 IC697MDL341. The 120/240 Volt AC 2 Amp
Isolated Output Module GE Fanuc 90-70…
IC697MDL350 The 120 Volt AC 0.5 Amp Output Module GE Fanuc 90-70
IC697MDL350 provides 32 output points in four isolated groups of 8
points each. GE Fanuc 90-70…
IC697MDL640 GE Fanuc 90-70 IC697MDL640 is a 125 Volt DC
Positive/Negative Logic, 16-Point Input Module. GE Fanuc 90-70
IC697MDL640 has Positive/Negative Logic…
IC697MDL651 The 5VDC, TTL Input Module GE Fanuc 90-70 IC697MDL651
provides 32 TTL compatible input points which are configured as one
group. GE Fanuc 90-70 IC697MDL651 is…
IC697MDL652 The 12 Volt DC Positive/Negative Logic Input Module GE
Fanuc 90-70 IC697MDL652 provides 32 input points in four isolated
groups of eight points each….
IC697MDL653 GE Fanuc 90-70 IC697MDL653 is a 24 Volt DC
Positive/Negative Logic, 32-Point Input Module. The GE Fanuc 90-70
IC697MDL653 has 32 Points – Four isolated groups…
IC697MDL654 The 48 Volt DC Pos/Neg Input Module GE Fanuc 90-70
IC697MDL654 provides 32 input points in four isolated groups of
eight points each. GE Fanuc 90-70…
IC697MDL671 Interrupt Module GE Fanuc 90-70 IC697MDL671 is a 14
Point wth 24 Volt DC Positive/Negative Logic. The GE Fanuc 90-70
IC697MDL671 16 points total – 4 isolated…
IC697MDL740 The 24/48 Volt DC 2 Amp Output Module GE Fanuc 90-70
IC697MDL740 provides 16 output points in four isolated groups of 4
points each. Each group of four…
IC697MDL750 The 24/48 Volt DC 0.5 Amp Output Module GE Fanuc 90-70
IC697MDL750 for the Programmable Logic Controller (PLC) provides 32
output points in four isolated…